|
Click to Choose Your Product:
| AUTOSEAL® Aria Stainless Steel Travel Mug
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by sliding the button down to lock, exposing the red "locked" area above the button.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Travel mug and lid are top-rack dishwasher safe.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
.jpg)
Click to view General Care & Use Instructions (all products)
|
| AUTOSEAL® Bella Double Wall Insulated Mug
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Travel mug and lid are top-rack dishwasher safe.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
|
AUTOSEAL® Elite Stainless Steel Travel Mug (sold only at QVC)
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Lid is top-rack dishwasher safe.
- Hand wash mug body.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
| AUTOSEAL® Elle Double Wall Insulated Mug
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Lid is top-rack dishwasher safe.
- Hand wash travel mug body.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
|
AUTOSEAL® Sport Stainless Steel Travel Mug
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Travel mug and lid are top-rack dishwasher safe.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
|
AUTOSEAL® West Loop Stainless Steel Travel Mug - 16 oz.
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- All lids are top-rack dishwasher safe.
- If you have purchased a mug that has a brushed stainless steel body (not colored/painted body), the body is top-rack dishwasher safe.
- If you have purchased a mug that has a COLORED/PAINTED body, it is recommended that the body be hand washed.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
|
AUTOSEAL® West Loop Stainless Steel Travel Mug - 20 oz.
WARNING:
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- Always press the AUTOSEAL® button when the tumbler is in the upright position prior to lifting it to drink. This will release any built-up pressure. Release button to seal mug.
- Keep out of reach of children when filled with hot liquids.
- Prior to drinking, check to ensure the lid is properly threaded to body and screwed down 100%. Button should be depressed to release pressure each time the lid is screwed on.
- If filling with boiling liquids, allow liquid to cool down for at least 3 minutes before sealing with the lid.
- Coffee brewed below boiling temperatures can be poured directly from coffee makers into the mug without waiting for liquid to cool down.
- Avoid accidental depressing of button by keeping button free and clear of other objects.
- Do not overfill. Fill liquids to just below the threading in the body.
- Do not microwave and do not freeze.
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
USAGE RECOMMENDATIONS:
- Suitable for hot and cold beverages.
- To screw the lid on easily and safely place lid on top of mug. Apply slight downward pressure and rotate counter-clockwise until you hear a click and lid falls into place. Proceed to rotate lid clockwise to tighten down.
- The AUTOSEAL® lid that came with your new purchase is designed to only fit your new Contigo® mug. Not for use with other products.
- AUTOSEAL® lid is designed to help prevent spills from accidental tipping.
- Following your purchase, wash all parts with hot soapy water before use. Rinse thoroughly and dry. Always store with lid removed to allow parts to dry completely.
- Lid is top-rack dishwasher safe.
- Hand wash mug body.
LID CLEANING TIPS:
Always rinse the lid immediately after each use. Store with lid removed to allow parts to dry completely.
Rinse drink spout and lid vent immediately after use, prior to putting into the dishwasher:
1. Turn lid so the underside is facing up and fill lid with hot soapy water.
2. Tilt the lid back and forth first towards the drink spout and then towards the button while pressing the button to allow the soapy water to rinse
through both the drink spout and the vent hole.
3. Repeat 1 and 2 a few times for best results.
Additional Cleaning Tips:
To clean the top of the lid:
1. Use a non-abrasive sponge or brush head/swab to clean the drink spout in the open and closed position.
2. Rinse while pressing the button to allow the soapy water to rinse through the drink spout.
Clean the underside of the lid with a non-abrasive sponge or swish in hot, soapy water.
If desired, a small, pipe-cleaner-style brush, small arts and crafts paint brush, or a cotton swab can be used to clean the inside of the
AUTOSEAL® mechanism. Turn lid so the underside is facing up and fill lid with hot soapy water. Run brush head or swab along the
following areas to ensure complete cleaning:
1. Underneath and along both sides of the center plastic piece of the lid. Reference "A" and "C" below.
2. Along both the inner and outer walls of the threading. Reference "B" below.
3. The underside of the spout. Reference "D" below.
Rinse repeatedly while pressing the button to allow the soapy water to rinse through the drink spout.
Click to view General Care & Use Instructions (all products)
|
Extreme Stainless Steel Travel Mug
- Careful. The beverage you are about to enjoy is very hot. For best results always use caution.
- The sealing lid is only designed to fit your Contigo® mug. Not for use with other products.
- Sealing lid is designed to help prevent spills from accidental tipping.
- Product can be used for both hot and cold liquids.
- Hand wash all parts with hot soapy water before use. Clean with lid in the open position. Rinse thoroughly and dry. Always store with lid removed.
- The lid closure tab should be in the open position when securing lid onto mug or when removing lid. Prior to drinking check to ensure the lid is secured tightly.
- Lid can be positioned for right- or left-handed drinkers.
- Lid is top-rack dishwasher safe. Body of the mug is hand wash only.
- Not recommended for carbonated beverages.
CAUTION:
- Do not use cleaners containing bleach, chlorine, abrasives, and/or other harsh chemicals.
- Do not microwave and do not freeze.
- Do not overfill. Fill liquids to just below the lid threading. Hot liquids can burn user.
- Do not fill with boiling liquids. Liquid temperatures should be 90 degrees C or less to avoid burning.
- Keep out of reach of children when filled with hot liquids.
Click to view General Care & Use Instructions (all products)
|
|
